 |
ROLL MASTER 1100
TURET SLITTER
|
|
|
This completely microprocessor controlled
Slitter Winder was
specifically designed to handle very thin film such as,
Thermal Transfer, Hot Stamp, Holographic Media …
|
 |
Sophistication has not compromised ease of use; although
many different
design features and programmable functions have been combined
into this
state of the art slitting machine, operator friendliness
is definitely one
of its strong suites. The RM 1100 is a veryflexible tool,
which we are
sure, will greatly enhance your production capabilities
|
 |
|
Slanted Leader table with pneumatic clamping
bars and vacuum supported cutting bars. Table is fully adjustable
to any leader configuration. Nip driven, shaftless leader
unwind for 3 piece leader with tape
holders for top and bottom feed. |
 |
Closed loop dancer controlled, driven shaftlessunwind
stand, with 6” air chucks. On the fly electrical side
shift controlled from either operator panel.Unwind mounted
on linear bearing tracks.
|
 |
Pneumatically operated razor slitting system.
Quick change magnetic blade holders for 20mm minimum Slit
width. Dual turrets with air rewind shafts and bearing type
rewind shaft supports. Air operated linear surface roller
assemblies with antistatic discharge bars.
|
 |
Touch screen operator interface for control
of all machine functions.
Internal closed loop rewind tension control with Taper tension.
Recipe utility for job storage.
|
 |
Servo motor torque controlled trim winder.
Adjustable speed and travel traversing feature. Operator adjustable
rewind tension. Quick release rewind shafts.
|
 |
Core box for rewind shaft loading / unloading.
Infinitely adjustable down to 25 mm ribbon width. Will accept
½” to 1 ¼ shaft size. Air gun for shaft
inflation. Table top mount.
|
 |
|
Quick change razor blade holder. Allows fast and accurate
positioning forquick job changes. Magnetic razor blade holding
feature for ultra fast Blade changes.
|
 |
Pneumatically operated rewind core notching device. Can
cut 4 x 8 mm notch for 1” and ½” cores.
Single or dual notch at 90 or 180 degrees.
|
 |
|
TECNICAL SPECIFICATIONS
- Max. running speed 300 M/min.
- Maxi. Web width 1100 mm
- Max. jumbo roll diameter 610 mm
- Unwind chuck diameter 152.4 mm
- Max. rewind diameter 125 mm
- Min. rewind shaft diameter 12.7mm
- Min. slitting width (smaller on request) 20 mm
- Winding technique locked core
- Air supply 6 bar
- Control voltage 24 VDC
- Power supply 400 VAC 3 phase
- Foot print L x W x H 2.4 M x 1.5 M x 1.8 M
|
|
INCLUDED IN BASE PRICE OF MACHINE:
- Main structure complete.
- Closed loop controlled shaftless unwind stand
with electrical side shift feature.
- Leader table with air operated clamping bars, two
vacuum supported cutting bars and three film
support bars.
- Motorized, nip driven leader unwind with three
shaftless unwinds and five tape dispensers for
top or bottom feed.
- Servo driven main drive assembly with two
nipped pull rollers.
- One bow roller and all necessary idler rollers.
- Razor in air slitting station with 10 pieces quick
change magnetic blade holders.
- Two air operated surface roller assemblies with
integrated antistatic discharge bars.
- Servo driven dual turret assemblies
- Four 1 inch air rewind shafts with bearing type
shaft supports.
- Two traversing trim winders with servo tension
control.
- Touch screen operator panel.
|
|
FOR A PDF COPY OF THE COMPLETE DOCUMENT WITH
PRICING INFORMATION, PLEASE CLICK THE LINK BELOW
|
|
| |
